Feeds:
Posts
Comments

Archive for the ‘gear reviews’ Category

Gotta Love Spring Fever!

Posted in clean boost, effect pedals, Effects, GAS, gear, gear reviews, guitar, guitar effects, guitar gear, guitar gear reviews, guitar pedals, Guitars, Music, musicians, new gear, pedals, reverb, Tone, tagged , , , , , , , , , , , , , , , , , on November 11, 2010| Leave a Comment »

No, not the sexual kind – though we do like that – but the spring reverb kind. 🙂 Specifically, I’m talking about the Tone Candy Spring Fever. I reviewed the Spring Fever back in May, and gave it a 4.5 Tone Bones. But now that I’ve got it and after spending a few hours with it last night, I’m now giving it 5.0 Tone Bones! Here’s why:

  1. As I said in my original review, the Spring Fever is just about the best spring reverb pedal I’ve ever played. It sounds incredibly realistic, and unlike many of the digital varieties I’ve played, while it’s jangly with some top-end, it also doesn’t lose bottom end, so your tone stays nice and rich. That’s a little disconcerting to some folks because they’re used to a brighter tone, but for me, the retention of the bottom end is really what sold me on its tone, plus with the Spring Fever, you can go from subtle spring ‘verb, to rich, spacious, swirling surf tones, so there’s lots of variety on tap.
  2. What I didn’t get to test out in my original audition of the Spring Fever was its Volume knob which also acts as a clean boost if you turn the Reverb and Mix knobs all the way down. I’m not sure how much boost the pedal adds, but there’s enough boost on tap to slam the front end of your amp with loads of gain.

I particularly like the Volume knob because it solves a real problem for me when I play my acoustic gigs at venues where I have to plug directly into a PA board. My acoustics’ pickups don’t have much gain, and I usually have to crank up the volume faders on the board, which can be problematic as it makes it difficult to balance out the guitars’ volume with my vocals. I’ve solved this in the past by lugging my Presonus TUBEPre preamp with me, but that’s a bit of a pain to lug (read: extra gear, not because it’s heavy), and requires a separate 12V power supply. The Volume knob on the Spring Fever eliminates the need for me to bring a preamp with me. Nice.

If I have one complaint of the pedal, it has to be its finicky nature with power supplies, and will add some noise to the signal. Mike Marino explains this on the Spring Fever product page, and recommends some power supplies to use, such as the 1-Spot. I used the 1-Spot in my clips, and when the Spring Fever was activated, there was a slight, but noticeable hiss. This has to do with the power supply, and not the pedal. This also happens when I use my MXR Carbon Copy with the 1-Spot. When I hook it up to a regulated power supply like a Dunlop DC Brick, the pedal is as quiet as can be. So despite Mike’s recommendation about the 1-Spot, don’t use it. Get a regulated power supply like the DC Brick. Luckily, I have an extra DC Brick, so that will be powering my mini board.

How It Sounds

As I said, the Spring Fever is about the best spring reverb pedal I’ve ever played! Capable of producing a wide range of reverb, this pedal will be a permanent fixture on my board! I’ve still got to play around with it some more, but I recorded a few clips to give you an idea of what it can do. The clips below were all recorded using my 1958 Fender Champ output to a Jensen Jet Falcon 1 X 12. I start out each clip with a dry signal, then play it again with some “grease.” What that pedal adds with respect to spaciousness is amazing! All the clean clips were recorded at unity volume, while the dirty clips were played with the amp turned up to about 2pm, and the boost at 1pm with Mix and Reverb completely off. I wanted to demonstrate the clean boost and its effect on an overdriven amp.

Les Paul, Middle Pickup, Fingerstyle. Reverb: 11am, Mix:10 am

Left Channel: Les Paul Middle Pickup, Reverb and Mix same settings as above
Right Channel: Les Paul Neck Pickup, Reverb: Dimed, Mix: 8pm

I love the right channel track on this clip. Turned up all the way, you get this cavernous room sound, but with the Mix set real low, it becomes a much more subtle effect, providing almost a delay-like ambience without the echos.

Squier CV Tele Middle Pickup. Reverb: 10am, Mix 10am
MXR Carbon Copy with long delay time, Mix at about 10am

Les Paul Middle Pickup (biased toward bridge), Volume: 2pm, Mix/Reverb Off

Squier CV Tele Bridge Pickup (biased toward bridge), Volume: 2pm, Mix/Reverb Off

Overall Impression

Yeah, it’s pricey at $275, though you can find it at a lower price if you look. But I haven’t heard as a good a spring reverb pedal like this – ever. And the fact that it has a booster in it just rocks! For me, and especially for my acoustic gigs, this is a game changer!

Read Full Post »

Gear Review: VHT Special 6 Combo

Posted in 6V6, amplifier reviews, amplifiers, booster, GAS, gear, gear reviews, guitar, guitar gear, guitar gear reviews, guitar tone, guitarists, Guitars, Music, musicians, tagged , , , , , , , , , , , , , , on September 27, 2010| 7 Comments »

VHT Special 6 Combo
Summary: This is a hand-wired, solidly built tone machine that packs great features for an unbelievable price. The value proposition alone is enough to turn heads, but add superb tone to the equation and you have a winner!

Cons: None.

Features (as tested):

  • 6 Watts
  • One 6V6 Output Tube
  • One 12AX7 Preamp Tube
  • Volume and Tone Controls
  • Footswitchable Boost Mode
  • High/Low Power Switch (Pentode/Triode)
  • 10” VHT High-Sensitivity Speaker
  • 4, 8, and 16 Ohm Speaker Jacks
  • Mod-Friendly Eyelet-Type Board
  • Hand-wired In China

Price: $199 Street / $179 Street for Head

Tone Bone Score: 5.0 ~ Clean or dirty, this amp delivers the goods! The tone sweep is absolutely excellent giving you gorgeous, warm jazz cleans, to classic rock bite! Add the Hi/Lo power switch, and Push-Pull volume knob boost (also includes a footswitch), and you’ve got an amp that can live in a variety of musical genres.

About a week ago, I extolled virtues of the Marshall Class 5, and raved about how great it sounds. It’s a fantastic little amp, and I haven’t changed my opinion of it. But along came the VHT Special 6 and the game has completely changed. VHT raised the bar with Chinese-manufactured, low-cost, low-wattage amps by offering a hand-wired, super-well-built amp with fantastic features that can easily change the amp’s character for under $200 for a 1 X 10 combo.

I think the arrangements many gear manufacturers have made with overseas assemblers is great. Egnater is another example of a manufacturer doing it with great success. Design the gear here in the US, then partner with an overseas manufacturer to take advantage of their cheaper parts and labor, ensure that they meet a high standard of quality, then give the savings back to the customer. The top-of-the-line stuff can be saved for domestic production, but the stuff you want to get out to the masses can certainly be made elsewhere, and in much higher volumes and production rates. It’s a good model that many manufacturers have been following for years. I realize that I’m going to piss off some of the ultra-patriotic that will only buy stuff made in the USA; I myself prefer to buy US-made stuff, but it’s tough to argue with getting great tone for a great price, and that is EXACTLY what the VHT Special 6 and lots of other gear assembled overseas provide.

But enough toeing the political line. Let’s get into discussing the Special 6, shall we?

Fit and Finish and Features

The first thing I noticed when I first looked at the amp is how solid it looked. Picking it up revealed an amp that is no lightweight. I don’t know the exact weight, but the Special 6 is not lacking in heft. The cabinet is made of birch ply, and from what I could tell, fairly large transformers were used with the amp and those are heavy. Note that I’ve actually heard some conflicting information about the cabinet wood. Some say MDF, others say Baltic birch ply. Actually, it just doesn’t matter. The cabinet’s solid, and it works well as a resonance chamber for the speaker.

As far as cosmetics are concerned, the amp is covered in tolex with white piping around the front grille. The rear panel sports a partially open back that, like the Marshall Class 5, has a thin metal screen covering the opening. That’s a nice touch.

The control panel is super simple. You’ve got two chickenhead knobs for tone and volume, on/off switch, a three-way Hi/Lo Power / Standby switch (I dig that), and two input jacks for Lo and Hi input. The volume knob is a push-pull knob that when out, adds boost (sorry, not sure about the amount of boost). You can surmise just by these features that you can do a lot of tone shaping with this little beast. 🙂 The back panel has jacks for 4, 8, and 16 ohm speaker outs, plus a jack for switching between normal and boost.

Sound and Dynamics

Even with a 10″ speaker, the amp is capable of producing a variety of tones, from lush, Fender cleans, to ringing, AC15-like overdrive to gorgeous, smooth Plexi overdrive. I’m not kidding about this! Depending upon the pickup you’re using and where you set the tone knob, and other amp settings such as hi/lo input, pentode/triode mode, you can cover a wide range of tones! This is what is so SICK about this amp! It’s so damn versatile!

I played around with it in my studio this afternoon, getting ready to record some clips (which I’ll have in an upcoming article), and just for kicks, I unplugged the stock speaker and ran the amp out to my 2 X 12. Granted, there is a HUGE difference between a 2 X 12 and a little 10″ speaker, but in my experience, many low wattage amps still sound a little on the thin side even when going into a bigger cab; not so with the Special 6. It sounded big and ballsy; much more “big-amp-ish” than it’s diminutive power. That really came as a surprise, much like my surprise when I plugged the Reason Bambino into a big cab. It’s clear that just like the Reason guys, VHT didn’t want to just build a low-wattage amp. They wanted to build a great amp, period.

I also gigged with the amp in my weekly church gig yesterday afternoon, and it worked absolutely stellar! I kept the amp in high power mode, plugged into the high power input, set the tone and volume at 3pm each, then pulled the boost knob to activate the normal/boost footswitch. I didn’t use any effects at all as I just wanted the raw amp tones. I even tuned with my Peterson StroboClip so my signal from my guitar to the amp was completely direct. Note that even with a 10″ speaker, I still had to use an attenuator, and my trusty Aracom PRX150-Pro worked stellar with the amp.

During the gig, I mostly used the volume knob on my guitar to vary gain, whether in normal or boost mode. The amp responded so well to volume knob and pick attack. Even if I didn’t reduce the volume, and picked very lightly, I could clean up the sound. So sweet!

The only time I made any adjustments to the amp was when we did a song that I needed absolutely clean tones. I simply reduced the volume to around 11 am, then bypassed the attenuator. And the cleans were simply fantastic!

Made to Mod

Despite the fact that VHT says this amp is highly modifiable, I doubt that most people will do no more than swap tubes. I’ve seen some forum posts where people have made a couple of changes, but I’d say the majority of folks just won’t see a need to do that. But curious, for shits and giggles, I swapped out the stock 6V6 with a couple of different 50’s-era 6V6’s (GE and RCA). They each sounded beautiful as I expected, but quite frankly, they were just too smooth. The Chinese tube seems to be “hotter” and produces lots of harmonics; something my NOS tubes didn’t do. In my opinion, the Special 6 is meant to be a mini-rock machine. It won’t do really heavy stuff, but for 70’s and 80’s classic rock, it sits right in the sweet spot.

Overall Impression

I am thoroughly impressed with the VHT Special 6. Hand-wired, immensely versatile, plus fantastic tone for under $200? That’s tough to beat! And unlike other small, low-wattage amps that have only a volume and tone knob, the combination of inputs, low/hi power modes and boost make this an amp that can be used in a variety of ways. Big thumbs up, and 5 Tone Bones!

I’ll have clips in an upcoming article. Stay tuned!

Update: January 2, 2013

It has been awhile since I wrote the original article, and amazingly enough, I’m still using the Special 6. I did finally swap out tubes to 50’s era NOS for both pre-amp and power tubes, and I also swapped out the stock speaker and put in a Jensen Jet Electric Lightning. I use this amp frequently at my church gig where I don’t need a lot of volume since mic the amp and use the PA, and it is perfectly suited for that venue.

Even after all this time, I do have to say that I’m still thoroughly impressed with the tone of this little amp. When it’s cranked, and especially with the Electric Lightning speaker, the amp sounds SO much bigger than what its diminutive 6 watts would suggest. A lot of that has to do with how the speaker projects, but when cranked, that amp absolutely sings with tones of sustain and really sweet overtones. I love playing this amp with a Les Paul. The clean tones are gorgeous as well, and when I don’t hook it up to an attenuator, I just use pedals to get my distortion. From that perspective, the amp takes to pedals real well.

Finally, even with a simple, single EQ knob, the EQ works fantastically well with the amp. It’s kind of bright out of the box, so I normally just set the tone control to about 10 am. On some amps I’ve played, that muddies the tone a bit; but not with the Special 6. It simply makes the lower range stand out a bit more.

I’ve even been using the amp in the studio, over my DV Mark Little 4o and Aracom VRX’s (except where I need a heavier sound). It’s perfect for the studio.

Read Full Post »

Review & Gig Report: Mad Professor Deep Blue Delay

Posted in delay, delay pedals, effect pedals, Effects, GAS, gear, gear reviews, guitar, guitar effects, guitar gear, guitar gear reviews, guitar pedals, guitarists, Guitars, tagged , , , , , , , , , , , , , , , , on August 14, 2010| 7 Comments »

While I did a “mini review” of the Mad Professor Deep Blue Delay a couple of months ago, that was in a shop in a controlled environment, and though I played it for almost an hour, there’s no better test of gear than using it at a gig where nothing is predictable.

After I originally auditioned the pedal, I anguished for the last couple of months about getting it. Why? Simply because of its price: It is NOT a cheap pedal by any means (I got it for $335), and it was always easy for me to reason why not to get the pedal. However, I’ve been a bit disappointed with my VOX Time Machine when using it with my acoustic rig. I thought that since it performed so well with my electric rig, that it would translate well to my acoustic rig. That couldn’t be further from the truth. Truth be told, while the Time Machine simply kicks ass with my electric rig, my tone feels and sounds “processed” with my acoustic rig. The net result is that I stopped using it for my acoustic gigs.

I knew I had to get a good delay that would work well with my acoustic rig, and I also knew that after auditioning quite a few digital and analog delays at the shop, it was the Deep Blue Delay that spoke to me. But the price of the pedal made me shudder, so I put off the purchase for the last couple of months.

Then yesterday, in a moment of weakness, I purchased the pedal on my lunch break at work. Jordan, the sales guy I’ve been buying gear from at Gelb Music for years, swears by this pedal, and he just said, “Dude, I know the price is steep, but there’s none better than the the Deep Blue Delay. It’s always on my board, and it’s almost always on. The VOX Time Machine is a killer pedal (he sold me that one as well), but you know how the Deep Blue sounded with the APX900 (Yamaha – I bought that one from him too – though he didn’t make a recommendation that time 🙂 ) when you tested it a couple of months ago. Believe me, you won’t be disappointed.” Mind you, I trust Jordan’s advice implicitly. I’ve been buying gear from him for years, and have learned that when he raves about some gear, it’s not bullshit because he owns it or has gigged with it. And with the Deep Blue Delay, I’ve never witnessed him rave so much about a pedal!

So I am now the proud owner of the Mad Professor Deep Blue Delay, and like Jordan, I can’t rave enough about it! What about my Time Machine? It goes back on my electric rig board. I love that pedal because it has such a great sound with whatever electric guitar I use on it. But for acoustic, it’ll be the Deep Blue from now on.

Fit and Finish

With a gorgeous, shiny, blue powder coat finish, this is simply the most gorgeous pedal I have. I’m partial to blue, but the gloss is like a mirror, as the photos below show. If I have one nit, the blue LED is a bit difficult to see in bright lighting conditions, but that’s just small nit. Other than that, the pedal is solidly built. The knobs have good resistance without being tight, and the toggle switch is heavy duty. I’m not sure what kind of jacks were used but connectors snap into place nicely, so I’m assuming they’re fairly high-quality jacks.

Taking the back off the pedal, there are LOTS of wires connected to a foam-wrapped circuit board (that I didn’t want remove), so it’s clear that the Deep Blue Delay is completely hand-wired, save for the circuit board. The wires are all fairly heavy-gauge with thick shielding, which speaks to the quality of components used in the pedal. I didn’t want to lift the foam pad because the wires were so heavy and I didn’t want to have to deal with putting them back into place. 🙂 Mad Professor could’ve easily used thin-gauge wires for this pedal, but I like the fact that they opted for the heavier gauge.

This slideshow requires JavaScript.

How It Sounds

I know that I use the words “awesome” and “incredible” on this blog. After all, this is a “best of breed” type of site. So let’s just assume that the pedal can be described with those words, and I’ll take a different tack and describe what that sound does to me.

I know a piece of gear is incredible when it just makes me close my eyes and soak up the sound it produces. That’s the effect the Deep Blue Delay has on me. The delay effect, even at high levels is always smooth, and amazingly enough sounds so natural. There is nothing processed about this sound. And unlike other analog pedals I’ve played, the Deep Blue Delay doesn’t get dark, which is what has kept me from getting analog delays in the past.

At last night’s gig, I turned a disaster into a way to fully evaluate the Deep Blue Delay. With my acoustic rig, since I don’t have too many pedals, I use my BOSS TU-2 to power up the rest of my pedals. But last night, I had forgotten that I removed the TU-2 to use at a gig last week, so when I opened up my pedal bag, I was shocked to see my TU-2 missing. Luckily, I had left my 9V plug in the bag, so I figured that it was a great way to use the Deep Blue. So I plugged my guitar into the pedal, and it went straight into my Fishman SoloAmp.

I set up the pedal with the Delay and Repeat knobs at about 2pm, and the Level at 9am so I could get a nice, ambient sound that didn’t dominate. That created a hall-like effect that was simply delicious. I kept it at that setting for several songs. Then just as an experiment, I upped the level to 11, and then the skies parted and a voice rang from the heavens, “You have found s a sacred tone!” 🙂 Seriously though, I was completely blown away by what the pedal produced. The repeats were on the speedy side and the decay was a nice tail without being overbearing, and at that level, the wet/dry mix was just perfect!

The wonderful thing about the Deep Blue is that it seems like there’s a pre-delay built into the pedal. The one thing that sets this apart from other delays I’ve used is that at anything greater than low level settings, you get delay going right away. But even at 11am, whatever I was playing, whether finger picked or strummed, didn’t start repeating until there was space – or at least that was what it seemed like. Of course, at higher levels, the delay kicks in right away, but despite that, what you’re playing is invariably clear and doesn’t get washed out by the repeats.

Overall Impression

In other words, this truly is an incredible pedal. I’m still smarting just a little from the price, but as I haven’t played a delay for my acoustic as good as this – ever – it is well worth the price! I originally gave the Deep Blue pedal a 4.75 Tone Bones rating because of its cost. But my thinking now is that if that’s what it costs to get this kind of delay, then that’s what it costs, and I’m so much happier playing with this pedal in my signal chain. I’ve re-rated it as a 5 Tone Bones pedal. If you can afford it, this pedal will not disappoint; in fact, I’ll wager that it’ll make you practically squeal with joy!

About the Photos

Another hobby of mine – and no, I don’t sleep all that much – is photography. With this hobby, I don’t aspire to be a professional photographer, but I do like to take good photos. These photos were taken with a Nikon D40 with a f1.8 35mm fixed-length lens. All shots were taken in manual mode. I don’t remember the settings, but I shot about 60 photos and picked what I felt were the best shots. Then I used Adobe PhotoShop Elements to crop the photos and did a minimal amount of color correction on a couple of them. I believe that unless you’re going to make artistic enhancements to photos, you should set up your shots so you can “print” them immediately without color manipulation; that is, set up your camera so you don’t have to compensate later.

I know, this is a guitar gear blog, but going forward, I will be doing my own photos of gear. What I love about this particular set is that my camera caught the wonderful reflections off the shiny powder coating of the Deep Blue Delay. I find that marketing photos tend to be a bit too sterile. This is the best-looking pedal in my collection, and I wanted to do its look justice.

Read Full Post »

Gear Review: Sennheiser ew 172 (100 Series) G3 Instrument Wireless System

Posted in GAS, gear, gear reviews, guitar, guitar accessories, guitar gear, guitar gear reviews, guitarists, Guitars, Music, musicians, new gear, wireless guitar, tagged , , , , , , , , , , , , on August 10, 2010| 1 Comment »

Click for larger image

 Sennheiser ew 172 G3 Wireless System

Summary: If you’re looking for a great instrument wireless system that is both easy-to-use and a snap to set up, look no further!

Pros: 1680 available frequencies make this ideal for busy RF venues. Super easy to set up sensitivity levels. Transmitter sports a metal housing, so durability shouldn’t be an issue. Integrated guitar tuner in transmitter – works great! 25Hz low-end response – great for bass!

Cons: None.

Features:

  • Sturdy metal housing (transmitter and receiver)
  • 42 MHz bandwidth: 1680 tunable UHF frequencies for interference-free reception
  • Enhanced frequency bank system with up to 12 compatible frequencies
  • High-quality true diversity reception
  • Pilot tone squelch for eliminating RF interference when transmitter is turned off
  • Automatic frequency scan feature searches for available frequencies
  • Enhanced AF frequency range
  • Increased range for audio sensitivity
  • Wireless synchronization of transmitters via infrared interface
  • User-friendly menu operation with more control options
  • Illuminated graphic display (transmitter and receiver)
  • Auto-Lock function avoids accidental changing of settings
  • HDX compander for crystal-clear sound
  • Transmitter feature battery indicatation in 4 steps, also shown on receiver display
  • Programmable Mute function
  • Integrated Equalizer, Soundcheck mode and guitar tuner
  • Contacts for recharging BA 2015 accupack directly in the transmitter
  • Wide range of accessories adapts the system to any requirement

Price: $499 street

Tone Bone Score: 5.0 ~ I waited a LONG TIME to pull the trigger on a wireless system, and while I could’ve gotten a cheaper one that would work well, but it was hard to argue with the frequency coverage of this unit. The added features of a guitar tuner and EQ are great, but the ease of use factor really hit home with me as well.

As I mentioned above, I’ve been holding out a long time to get an instrument wireless system. When I finally pulled the trigger, I decided upon the Sennheiser G3 Wireless system; first and foremost because of the number of frequencies it has on tap, but honestly, also because it’s a name I trust as my performance mics are Sennheiser. I’m not being a cork-sniffer here. I swear by the brand because of the years of great performance I’ve gotten out of other Sennheiser equipment, so it stands to reason to trust it for something completely new.

As it turns out, true to my past experience with Sennheiser gear, there was absolutely nothing to be disappointed about with the wireless system. I took it to my church gig yesterday and it well, just worked, with no tweaking on my part; save for adjusting the sensitivity levels which I didn’t even think to do when I first opened up the box. In fact, I didn’t even read the manual when I took it out to try in my studio. I just attached the antennas to the receiver and plugged in the instrument wire into the transmitter, popped in the batteries, and let ‘er rip. It literally took less than a couple of minutes to get up and running. Insofar as my church gig is concerned, it was a great venue to put the unit through its paces, as there are potentially several wireless units in operation at one time, including my own wireless headset mic. I’ll talk more about the system’s operation below.

In any case, since this isn’t something that actually makes music, my review areas are going to be a bit different from my normal reviews.

Ease-of-use

As I indicated above, the unit’s pretty plug and play. But of course, you should check the sensitivity of the transmitter and receiver to make sure you’re not overdriving the unit. The LCD’s on both the transmitter and receiver makes setting sensitivity of either unit a snap. Both have an active meter and navigating to the sensitivity menu is just a couple of button presses. Sennheiser did a great job with the menus to make them only two levels deep, so you won’t have a problem getting to the parameter you need to set.

Durability

Both transmitter and receiver have very sturdy metal housings, so you needn’t worry about the units cracking. The transmitter has a real solid feel, and that instills confidence that you don’t have baby the unit, though of course, it’s always good to take care of gear.

Performance

Despite having 1680 UHF frequencies to scan, the receiver locks on to a usable frequency almost instantaneously once you turn it on. That is such a boon to using the unit. You switch it on, and you can use the unit.

One of the tests that my sound guy and I did was for me to walk a distance away from the receiver to see if it lost connection. I honestly don’t know what the maximum range is, but no matter how far I got away – I got about 100 feet away – the transmitter and receiver didn’t lose their connection to each other.

To save battery life, when I’m not playing I always switch off the transmitter on my headset mic. I did the same with the G3 in between songs. Every time I switched it back on, making a connection to the receiver only took a couple of seconds.

Final Verdict

I haven’t even begun to explore all the different features that this system has; one of which is a cable emulation mode that simulates a cable’s capacitance to ensure consistent operation of your effects and amp settings whether you’re plugged in or wireless. This a great feature. Admittedly, I didn’t use this, but my rig sounded pretty much the same with the same dynamics once I dialed in the sensitivity of both transmitter and receiver. Or it could be that the only thing I obsess about with my tone is if it sounds good and I’ve got dynamics. Minute changes due to changes in my chain don’t really bother me too much. So if I got a slight change in tone, since my sound with the G3 system was good with no loss in dynamics, it didn’t trigger anything displeasing with me.

But other than performance and sound and all the other stuff I discussed, going wireless is simply fantastic. I like to move around a lot when I perform, and not being tied to a spot by a cable is so freeing! It really boosted my ability to lead musical worship, and that is so COOL!

Read Full Post »

Aracom PRX150-DAG Video is out!!!

Posted in aracom amps, attenuator, GAS, gear, gear reviews, guitar, guitar gear, guitar gear reviews, guitarists, Guitars, Music, musicians, new gear, PRX150-DAG, tagged , , , , , , , , , , , , on August 9, 2010| Leave a Comment »

When you’ve got a guy like Lance Keltner singing the praises of your equipment and calling you a genius to boot, you must be doing something right. Jeff Aragaki of Aracom Amps is someone I’ve been praising for quite awhile, and I’m glad he’s finally getting the recognition he deserves.

As far as the DAG unit is concerned, that’s available exclusively through Destroy All Guitars. I’ve played through one of those units myself, and the high-cut filter works great, and definitely takes the edge off, without throwing a blanket over your tone and dynamics like many attenuators do that include one. If you have an amp that outputs lots of highs when cranked – or somehow hear high-frequency transients –  then the DAG unit is the way to go.

Coming up…

While Jeff has gained lots of popularity with his attenuators, often overlooked are his wonderful amplifiers of which I have three. In the next couple of days, I will be getting a 50 Watt Evolver to test out in my studio. I’m so excited! I’ve played through an Evolver at Jeff’s workshop and that amp has tons of balls! It’s definitely Marshall-esque, but with Jeff’s particular twists. I’m excited to be getting this unit for a full test!

Read Full Post »

Gear Review: 1987 Gibson ES-335 Custom St

Posted in es-335, gear reviews, guitar, guitar gear, guitar gear reviews, guitar reviews, guitarists, Guitars, inspiration, tagged , , , , , , , , , , , , , , on August 6, 2010| 8 Comments »

Click to enlarge. Sorry, phone pic
1987 Gibson ES-335 Custom St (St = Standard? Studio?) Summary: A rare beauty with a natural blonde finish with classic ES-335 tone!Pros: Absolutely tip-top shape for a guitar of this age. No major dings, but has been well-played. Sounds amazing!Cons: None.Features:

  • Mahogany neck
  • Bound carved flame maple top and maple sides and back
  • Bound ebony fretboard
  • Medium jumbo frets
  • Bone nut
  • Original chrome hardware (look like Tone Pros)
  • Original chrome pickup covers
  • 60’s-style lower profile neck
  • 50’s-style pickup wiring (either volume knob acts as a master, but the tone controls have a different cap value that doesn’t throw a blanket over your tone when you turn it down – this is crucial for playing in the bridge pickup).

Tone Bone Score: 5.0 ~ This guitar sounds and plays like a dream! While the action is a just a tad higher than I like it, the guitar still plays ultra-smooth.

I already talked about how I happened to get this guitar, so I won’t bother rehashing the details. Suffice it to say that I got this guitar for an absolute steal. In a way, this guitar is sort of redemption for me having sold my original ES-335 a couple of years ago when times were tough. So getting this guitar is a real milestone for me.

Fit and Finish

For a 23 year old guitar, it is in absolutely amazing shape. The body has some very minuscule dings in it that fortunately don’t penetrate the finish. I didn’t notice any checking in the gloss either, though that may occur after a few more years if the finish Gibson used was a nitro lacquer. The hardware is aged as to be expected, though there’s a little oxidation in the brass stop tailpiece that can easily be removed. The pick guard has pick marks on it, but no scratches and all the joints are perfect. There’s some fret wear, but nothing major where the frets would have to be replaced. As for the fretboard itself, it’s gorgeous. I love ebony fretboards as they’re so smooth to the touch, and it makes bending a breeze. The back of the guitar has a few nicks that don’t penetrate the finish – and no buckle rash. All in all, for as much as this guitar has been played, I’m just amazed at its overall condition.

Here are some pictures I took with my cell phone. Sorry if the quality is low. I’ll have better ones later…

How It Sounds

This guitar has all the tone I was expecting out of an ES-335, but as it has been broken in and the wood aged, the tone is A LOT richer than what I remember with my original ‘335. As far as pickup positions go, there are three as usual, though I understand that some models did have coil-tapped humbuckers; not this model, though.

I’ve always loved the gorgeous, deep tones of the neck pickup on an ES-335 and this guitar doesn’t disappoint in that department. This is where the ES-335 gets very close to the deep, rich tones of an archtop, but it’s well, different…

Kicking in the bridge pickup in the middle position gives the ES-335 its distinctive “hollow” tone. It’s really hard to describe, but that I’m a firm believer that that middle pickup selector position is what draws people to this guitar. It certainly is one of the main things tonally that originally drew me to the ES-335 in the first place! With the bridge dimed and adding more or less neck pickup, you can get tons of great tones!

The bridge pickup is bright as to be expected – perhaps a bit too bright – but the wonderful tone knob nicely takes the edge off the brightness. I did notice that the bridge pickup is not significantly louder than the neck pickup, which leads me to believe that the original owner lowered the height of that pickup. When I get home from vacation, I’m going to raise it a bit because I prefer to have that dramatic change in volume.

In any case, here are some clips:

Neck pickup, clean

I love the haunting character of the neck pickup on and ES-335. The wonderful thing about this pickup is that it produces a very deep tone, without sounding like an acoustic. Adding a little reverb “grease” only accentuates the haunting effect.

Middle position, with some grind for rhythm; bridge pickup for lead.

In this, I have the bridge dimed, and the neck about halfway for the rhythm part. The lead is just the wide-open bridge pickup. Notice that it’s bright and almost twangy.

Middle position, clean; both rhythm and lead

I had to do a bit of a tribute to the great Andy Summers with this last clip… 🙂 I added a touch of reverb and chorus to get that “Every Breath You Take” vibe.

For all the clips, since I’m on vacation, I don’t have an amp, but I always carry around an IK Multimedia StealthPlug to facilitate my songwriting or, in this case, create clips. I used AmpliTube Fender. For the clean clips, I used a ’65 Twin Reverb model, and for the crunchy clip, I used a ’59 Bassman.

Cool Funk Lead

There are two parts to this next clip. In the first part, I play in the neck position, then switch over to the bridge in the second part plus attack a lot more. Unlike a Les Paul, the 335 doesn’t sustain as much, but that’s not a bad thing. The net result is that overdrive tones tend to be much more tight and focused. BTW, the amp used here was an Aracom PLX18BB in its drive channel.

Overall Impression

This guitar really moves me. She plays so sweet and sounds so good that I truly am inspired. Of course, the price I happened to pay for it didn’t hurt at all, but irrespective of my price, I’d still give this guitar 5 Tone Bones. It’s really an incredible guitar! I can’t wait to get it home and to a luthier for a professional setup. The shop owner did a pretty good job of setting the guitar up, but he strung it with 11-53’s which, while certainly playable, aren’t really my cup of tea. I’ll have the shop put on a set of pure nickel 10’s.

Read Full Post »

Gear Review: Peavey Classic 30 Amp

Posted in amplifier reviews, amplifiers, amps, buying gear, EL84, GAS, gear, gear reviews, guitar, guitar gear, guitar gear reviews, guitarists, Guitars, tagged , , , , , , , , , , on August 2, 2010| 2 Comments »



Peavey Classic 30 Amp

Summary: Great looks, great sound, and at a GREAT price!

Pros: Beautiful cleans with a sweet, airy reverb, and smooth overdrive tones

Cons: This is a nit, but I was a bit annoyed at the labeling of Pre- and Post- volume controls on the Lead channel. Why not just follow convention? It’s obvious that “Pre” is volume, and “Post” is master. But when I first saw it, I wasn’t quite sure what to make of them until I turned the amp on.

Features (from the Peavey site):

  • 30 watts (rms) into 16 or 8 ohms
  • Four EL84s and three 12AX7s
  • 12 inch Blue Marvel® speaker
  • 2-channel preamp
  • Pre- and post-gain controls on lead channel
  • Normal volume control on clean channel
  • 3-band passive EQ (bass, middle, treble)
  • Boost switch
  • Reverb level control
  • Effects loop
  • Footswitch selectable channel switching and reverb
  • External speaker capability
  • Chrome-plated chassis
  • Classic tweed covering
  • Footswitch optional (not included)
  • Weight Unpacked: 39.50 lb(17.917 kg)
  • Weight Packed: 46.00 lb(20.865 kg)
  • Width Packed: 13″(33.02 cm)
  • Depth Packed: 21.5″(54.61 cm)
  • Height Packed: 19.25″(48.895 cm)

Price: $599 street

Tone Bone Score: 5.0 ~ Even my little nit couldn’t keep this amp from getting my top score. It’s simply a great-sounding amp!

I’ve been a big proponent of: If it sounds good to you, then brand and price don’t matter. This goes back to my very first guitar, a Yamaha FG-335 Acoustic that my dad bought me for my 18th birthday. I still have that guitar. But I remember a jam about 25 years ago I was having with my brother at a party. We were sitting in our living room, and we pulled out our guitars to have a jam and singalong. When I got my guitar out of its case, my brother remarked facetiously upon seeing its worn condition, “Dude, you should turn that into a beach guitar.” I just looked at him blankly and replied, “Nope. It may not look like much, but it has a great sound. Why the f&%k would I want to trash it? I’ll never get rid of this guitar!” Ahh… brotherly competition. 🙂 But I digress…

The point of me mentioning that is that nowadays with boutique gear being all the rage with “tube” this, “mustard cap” that, “hand-wired” this, etc., it’s so easy to dismiss some excellent gear that sounds absolutely KILLER! If you can get said killer-sounding gear at a fantastic price, then that’s even better. Now I admit that I have some expensive gear, but not once have I purchased gear because of a name or because someone told me to buy something because they love it. I suppose with this blog you might accuse me of doing just that, but I always suggest people try things out for themselves before making any buying decisions. Damn! Again I digress! Let’s get on the with the review, shall we?

Fit and Finish

Talk about vintage mojo! The first time I saw this amp in a local shop, I was stunned by its looks. With its vintage-style front panel and dark brown cloth grille, and tweed covering with chrome-plated corner protectors; what’s not to like? Weight-wise, at 40 lbs, it’s not light, but it’s also not a behemoth that you can’t lug easily into a gig. And don’t let the small size of its cabinet fool you: It’s quite resonant, but more importantly, its size doesn’t make it unweildy in the slightest. Simply put, the Classic 30 just plain looks great!

How It Sounds

In my test, I used a Squier Classic Vibe Tele 50’s, a Custom Shop Strat, and a Les Paul Standard. I always start out all my tests with the amp clean, and playing finger-style. No matter what guitar I used, the cleans were absolutely spectacular. I love EL84 cleans. They’re sparkly and chimey, and the Classic 30 simply delivered that EL84 clean goodness! The single coils sounded chimey as expected, but I totally dug the cleans with the LP! Adding a bit of grease with the reverb brought out the  lush, deep tones of the Les Paul nicely. I believe the reverb is a digital reverb, but who the hell cares? It sounds incredible! I guess that’s the point I was trying to make above. If something works well, it doesn’t matter what it’s made of.

As far as overdrive is concerned, as its name implies, the Classic 30 isn’t going to get you modern high-gain overdrive tones, but there’s tons of overdrive on tap. Once I dialed in the Pre and Post volume control balances, I was able to get nice overdrive tones that weren’t at all harsh, no matter how hard I pushed the amp. Since I was in a shop, I didn’t get a chance to record clips, but here are some clips from Peavey:

Clean

Clean, Reverb

Channel 2 Flat

Channel 2 Preamp

Channel 2 Boost

As you heard, great tones out of this little beastie. Even completely dimed, you don’t get over the top overdrive, but for classic rock and blues, this is a GREAT amp. That Blue Marvel 12″ speaker works great in this cab!

Overall Impressions

At $599, this amp looks and sounds as good as many boutique amps I’ve played. I love this amp, and it’s definitely going to be added to my amp collection. 🙂 I didn’t get to try out the effects loop, but I love the fact that it has one. It just adds to its versatility. If you’re looking for a vintage-style amp for a great price, this is definitely an amp to consider!

Read Full Post »

Gear Review: 1959 Les Paul Replica

Posted in GAS, gear, gear reviews, guitar, guitar gear, guitar gear reviews, guitarists, Guitars, les paul, Music, musicians, tagged , , , , , , , , , , , , , on July 19, 2010| 4 Comments »


Click to enlarge

 1959 Les Paul Replica

Summary: About as close as you can get to the real deal without paying hundreds of thousands of dollars.

Pros: Bright and super smooth tone, and sustain that’s absolutely to die for! This guitar is everything I imagined a ’59 Les Paul to sound and play like. Sounds and plays better than any Gibson re-issue I’ve ever played.

Cons: None

Features:

  • One piece Honduran (Old Growth) Mahogany body and neck (long tenon), 1959 neck profile
  • Brazilian rosewood fretboard with trap inlays
  • Lightly figured (realistic) maple top
  • Holly headstock veneer
  • RS Guitarworks (Winchester, KY) Nitro Lacquer finish with light aging in a Perryburst (Joe Perry burst colors), includes RS Guitarworks Certificate of Authenticity
  • PLEK and nut work
  • RS aluminum tailpiece
  • Tonepros AVRII bridge (Locking) ABR-1 Bridge with Maple Flame Mod (extra long stainless steel bridge studs)
  • Pots and Tone Capacitors from RS Guitarworks
  • Bone Nut
  • Wolfetone Dr. Vintage pickups with aged Nickel covers
  • Single line Kluson tuners
  • Weighs 9.68 lbs and is a rock machine
  • Year Built:  2008

Price: Vary from $4000 to  $20,000 depending upon who builds it (more on that below)

Tone Bone Score: 5.0 ~ This guitar is a dream come true! I recently wrote on my Facebook status: “There are guitars and then there are Les Pauls. There is no substitute.”

The first thing you’ll notice in the review is that I didn’t name the luthier of this guitar. That’s because I didn’t want to “out” the luthier, lest Gibson finds out and sues them for copyright infringement; that’s how close these replicas get to the original. But despite the risk of litigation, there’s an incredibly active underground market for these replicas, and having played around with this one for a few days, I don’t think that market will ever die. BTW, if you want to know who the luthier is, just send me an e-mail (goofydawg “|” guitargear.org), or if you’re on TGP, send me a PM.

Besides, replicas like this put Gibson back on the relevance map. Can you say Slash and GnR’s “Appetite for Destruction?” Whether or not Gibson likes it, the replica that Slash played made the Les Paul popular among guitarists again.

Forget how close it may come to the sound, feel, and dynamics of the original. Playing this guitar is like a religious experience! With this particular model, the original owner had the neck slightly tapered near the heal to relieve some of that “baseball bat” girth. It worked marvelously! Combined with the PLEK treatment, this guitar is absolutely easy to play. I usually have to take a few days to get to know the feel of a new neck. I even had to do this with my beloved Gibson Nighthawk. But with this guitar, I felt right at home!

Weight-wise, it has some heft at 9.6 lbs., but it’s so comfortable, and once I started playing, I completely forgot about the weight.

Here are some pictures:

Pictures courtesy of Bennie Delumpa (my son).

Fit and Finish

As you can see from the pictures, the guitar has been lightly relicked. I’m not normally a fan of aging a perfectly good guitar, but the purpose behind the aging was to produce a guitar that looked like a well-taken-care-of guitar from 1959. It has a couple of nicks on the binding of the body, and the lacquer has been very, very lightly checked. But other than that, it’s gorgeous.

How It Sounds

Unfortunately, my studio is still in a bit of disarray after the construction I had done on my house, so I don’t have my usual sound clips. But all I can say about the tone of this guitar is that it is nothing short of spectacular. The tone is on the brighter side of midrange, but the guitar produces all sorts of overtones and harmonics. The pickups used in the guitar are not hot at all, but that just makes it real smooth. Another thing is that the cap values used for the tone knobs make them quite usable. You can really knock the tone down, and the tone will not muddy up. I love that, as it gives me that much more tone shaping capabilities that I can do right at the guitar, as opposed to doing it at the amp.

The guitar also sports the classic Les Paul “bloom” as the body resonates, and boy does it resonate! Pluck a string, and you get your note, and then the body starts resonating, and you can hear AND feel the swell of the string vibrations as they course through the tone woods. I just close my eyes and go off to Never-never land.

There’s a lot to be said about old growth wood that has been drying for 50 years. Jeff Aragaki, who is quite knowledgeable about Les Pauls (he has many) is convinced that the combination of materials (old growth woods, hide glue, nitro-cellulose lacquer, correct hardware, etc.) that were used on this guitar make its sound that special. I really have never played a guitar that sounds and responds to like this!

I was just thinking that once I do manage to get a recording of this guitar, it just won’t do justice to the feel and dynamics of this spectacular specimen. I’ll hopefully be able to capture at least some of what I’m talking about.

Overall Impression

As I said above, forget about how close it may come to the original. I’ve never played a guitar that felt and sounded as good as this. I’ve never played a real ’59, but this guitar just oozes Les Paul goodness, and it’s everything I believe a Les Paul should be!

Read Full Post »

DBZ Guitars Receives “Best In Show” Award at 2010 Summer NAMM

Posted in GAS, gear, gear announcements, gear reviews, guitar, guitar gear, guitar gear reviews, guitar reviews, guitarists, Guitars, Music, musicians, new gear, tagged , , , , , , , , , , on July 6, 2010| 4 Comments »

Even though I got this news via a press release, it doesn’t surprise me at all that DBZ won the Best In Show award this year. I’ve been quietly following DBZ since they hit the scene, and I’ve appreciated what Dean Zelinsky  (founder of DBZ and famous for Dean Guitars) has been trying to accomplish with his guitars from the start; that is, build great looking, great sounding, and great playing guitars at a GREAT price. Yeah, that’s a common formula, and lots of people try to do that, but Dean has accomplished that.

Take, for instance, the Imperial Premier model to the left. I had the chance to hold and play around with one of these exact models in Transparent Wine a couple of weeks ago (didn’t get to plug it in, though hopefully the DBZ rep will let me borrow one for a review). The Imperial has some classic styling – it’s shaped very similarly to a Gibson SG, but that’s where the similarities end. If you look at the picture to the right, you’ll see how incredibly thin the body is. That makes for a super, super, super light weight. All I could say when I first picked it up was, “Wow!”

Now you might think that that would never fly, but I have to tell you, that guitar felt absolutely wonderful, and I could feel the string vibrations resonating through the body as I played. The soft v-shape of the neck stands for Very comfortable. The fretboard is nice and smooth. DBZ calls it “ebonized” rosewood – not sure what that means, but it’s as smooth as ebony, and I just love the feel of ebony fretboards.

Unfortunately, I didn’t get a chance to plug it in because I was busy picking up my Fishman Solo Amp. But just based upon my initial inspection, and just holding it it in my hands, if I wasn’t getting the Fishman, I wouldn’t have let the rep leave the shop with the guitar. Yup, I was THAT impressed! Even the store manager was completely blown away by the guitar. He’s a jazz player, and while he said he prefers archtops, he loved that guitar.

Here are some specs:

  • Construction/Scale: Set Neck 24.75″
  • Body: Mahogany/Maple Top
  • Flamed Maple Top
  • Natural Scrape Binding
  • Fingerboard: Ebonized Rosewood
  • Neck: Mahogany Soft V Neck
  • Frets: 22
  • Inlays: Premier Series
  • Pickups: DBZB/DBZ5
  • Electronics: Vol/Tone/3-way
  • Tuners: Grover
  • Hardware: Gold
  • Bridge: DBZ Custom Stop Tail

Pretty nice features. You can see more pictures and other information on the DBZ site.

Here’s the real kicker: You can get this guitar for $649 online!!! Fat Tone Guitars outside of Chicago has these in stock. So how is the price so low? Simply put, it’s due to technology. Dean Zelinsky isn’t shy nor embarrassed by this blatant use of tech to build guitars. And why not? With computerized routers, you can ensure build consistency. Plus, I believe all the heavy work is done overseas, so that keeps the prices down. Even though I try to stick to US-made gear where I can, in the end, geographic location is far less important to me than how the gear plays and sounds.

DBZ is still trying to build its dealer base, but I encourage you to check one out if there’s a shop near you.

Read Full Post »

Quick Review: Groove Tubes GT-6L6GE US Re-issues

Posted in 6L6, GAS, gear, gear reviews, guitar, guitar gear, guitar gear reviews, guitar tone, guitarists, Guitars, Music, musicians, NOS, tubes, tagged , , , , , , , , , , , , , on June 18, 2010| 1 Comment »

If you read this blog with regularity, you know that I love NOS tubes. Who knows? Maybe I’m being a cork-sniffer, but the significant impact NOS tubes have had on my amps has led me to preferring them over new production tubes. Unfortunately, NOS tubes are getting scarcer and scarcer, so I suppose that eventually I’ll  have to get new production tubes.

Now a company that I’ve tended to steer away from is Groove Tubes, mainly because they’re just re-labeler of various OEM tubes. They just measure voltage, match ’em up, relabel them and sell them as their brand. Nothing wrong with that, but I haven’t met a Groove Tubes tube that I’ve liked, until I discovered the Groove Tubes GT-6L6GE Re-issues.

Before I go on, I should clarify that I’m not talking about the current production 6L6GE’s, which are assembled overseas. The tubes I’m talking about were made in the USA up until about 2003, as far as I can tell.

What makes these tubes special is that they’re constructed of NOS materials (except the glass), and to the same specs as the original GE 6L6’s of old. Plus they were constructed in Southern California, so the quality is incredible. These tubes rock! To be honest, I’m not sure of all the details of their production, but I got the information from Brent Jesse @ audiotubes.com who recommended them to me.

I bought two sets so I could have a spare set, and have been in tonal heaven with my Hot Rod Deluxe! The cleans are lush and deep, and the overdrive is creamy smooth. I have other GE power tubes, and I’ve gotten used to their smooth distortion. These GT-6L6GE’s are no exception! In addition to their smooth breakup, they also don’t compress much, which is another thing I just dig. I prefer a more open distortion.

I compared these to both JJ’s and regular Groove Tube 6L6GT’s, and these just blow them away. The JJ’s and GT’s have nice, clear cleans, but forget about their tone when cranked up. The tone is harsh and gritty, even if I bias them a little hotter than spec; whereas the 6L6GE’s remind me of the breakup I get from my Plexi clone – without hot biasing! Amazing!

As these are no longer in production (don’t confuse these with the new 6L6GE’s), they’re a bit more expensive than the new production 6L6GE’s; $80 per pair as opposed to $55-$58 a pair. And because they have the same labeling as the new ones, it’s hard to tell them apart. So I recommend that if you want to get a pair, get them from a source you trust. As I mentioned, I get them from Brent Jesse Recording and Audio, and having purchased several tubes from him, I trust him implicitly.

All that said, I will be getting a set of the new production tubes to make a comparison, as they are also made with NOS materials, though assembled overseas. Who knows? They may just sound killer as well!

Read Full Post »

« Newer Posts - Older Posts »